How to install windows on multiple computers at same time: AOMEI Image Deploy

How to install windows 10 on multiple computers at the same time

Can I install windows 7 on multiple computers How to install windows 10 on multiple computers at same time How to install windows 10 on many computers at the same time Can you install windows on multiple computers

Ever wondered what is the easiest way to deploy the image of an operating system to multiple computers at once instead of resetting or installing the system image on multiple computers one by one?

For example, you need to have windows installed on 30 computers including software, fixes, drivers, etc.

Doing so on a separate computer will take a lot of time. AOMEI Image Deploy offers you a simple solution that transfers system images to dozens of computers at once.

It is essentially free development and cloning software that supports the development, restoration of an image on many computers over the network.

The recovery process is displayed as a percentage. The server will receive a query about whether the restore is successful and can handle all clients in remote areas.

These features simply allow you to follow the steps one step at a time to complete the deployment of the clients on the same LAN network.

It automatically distributes a different computer name and IP address for the clients and ensures that they can log on properly on the network after logging into the operating system.

In fact, you can pre-install the remote control software on the system image. When the clients are connected to the Internet, you can operate later on clients in remote areas.

The AOME Universal Restore technique supports the deployment of system image on many clients even with different hardware (for example different CPUs and motherboards) and ensures that the system starts up properly on clients after installation.

To use the tool you first need to log into the BIOS of each computer separately and configure the clients to boot from the network.

Supports the development (restoration or cloning) of a system image or system disk image on multiple computers over a local area network.

The whole process as you understand it is not suitable for beginners and can be difficult for even the most advanced.

However, below are the steps to follow, and of course, I give you the link to read the full instructions from the app developer’s website.


Can I install windows 7 on multiple computers

How to install windows 10 on multiple computers at the same time

How to install windows 10 on many computers at the same time

Can you install windows on multiple computers 

Yes!! Below are the stapes to do your work easily


1. Use “Create Windows PE Auto-Create” or “Create AOMEI Windows PE ISO Manual Boot” to create an ISO PE ISO file that includes the AOMEI Image Deploy program. Select “Create Windows PE Auto Mode“, and then click Next, the program will automatically create the Windows PE ISO file in the installation directory of this program.

Select “Create Windows PE Auto Mode” and then click “Make WinPE“, you will be taken to the interface where you can manually create Windows PE ISO. You can click “Add Drivers” to add device drivers to Windows PE ISO if needed.

Then complete the creation of Windows PE ISO step by step. When done, go back to the main interface and click “Search” to select the ISO file created.

2. Select “Enable DHCP” if needed.

Note (1)
To install correctly, there should be only one DHCP server in the network because many DHCP servers will cause a bad IP address allocation for the client. “DHCP Enabled” is the built-in DHCP server configuration feature. Once you see the message “Service started, waiting for connection”, then you can run on clients.

Note (2)
Clients must wait for startup until the “Service started, waiting for connection …” prompt. Otherwise, they cannot start successfully. To boot the clients you have to set Network Boot as the first boot device through Bios or let the clients boot directly from the network. If your BIOS is UEFI mode, you will need to set “UEFI and Legacy” or “Legacy Only” to start the client computers.

(If the BIOS does not support UEFI, you can ignore the previous operating step). Then wait for all the clients to start successfully, and then check the “I confirm all clients that need to be available on the network” option and click the “Next” button to access the reset settings page.

3. In the “Select a backup file” option you can only select the image file or disk image file created by AOMEI Backupper with the “.adi” file name in the Shared Network or NAS folder. Click “Search” to open the page to select an image and click “Add device or NAS” to add the network share directory or NAS share directory and select the image file or the disk image file with the file name “there.

4. “Select Clients”: select the clients from the list. “Destination Disk Number”: specify which disk the client should deploy the image (disk number starts from 0-256). “Extended Computers”: specify the number of client computers to be restored or deployed at the same time, at least 1 and at least 3.

Note (3)

Restore, Expand will delete all the partitions on the destination disk, so make sure that the specified disk numbers are the same as the disks that need to be restored to the clients. Generally, if the client has only one disk, then the disk number is “0”.

The source data is transmitted over the network so that if the network pressure is increased if the “developing computers” are set to excessively high levels, this will also slow down the transfer speed and the recovery – development speed.

Therefore, you must specify the appropriate number based on hardware devices such as network cards and network cable. The recommended number is 5.

If AOMEI Image Deploy Free is installed on the server, only a maximum of 20 computers can be selected. if AOMEI Image Deploy Free is installed on the PC operating system, an unlimited number of computers can be selected.

5. Select “Setup” to configure the reset settings “Set computer name”: set the client name after reset/deployment. “IP Setup”: Configure the IP address and DNS server of the client after reset/deployment.

The client’s name and IP address can be quickly defined as your decision. “Universal Restore”: specify whether you need to use “Universal Restore” to continue the reset or not.

READ ANOTHER: HDD monitoring software free: DiskGenius

If client hardware, such as CPU, motherboard, is not the same as the source computer in the system image file, select “Universal Restore” Note: When setting the computer name and IP address, try to avoid setting the computer name and IP address you have already used with the LAN. “Set IP” and “Universal Restore” is only available in the technical version of AOMEI Image Deploy.

6. Click the “Start Development” button to enter the page to continue the rollback/deployment.

You can use “Shut Down PC” or “Restart PC” to set whether to shut down or restart the computer after the client restarts. You can check out the development/recovery of progress here.

Developed clients can normally load the system.


Stay on op - Ge the daily news in your inbox